HL7 Terminology (THO)
3.0.0 - Publication

This page is part of the HL7 Terminology (v3.0.0: Release) based on FHIR R4. The current version which supercedes this version is 5.2.0. For a full list of available versions, see the Directory of published versions

ValueSet: ActRelationshipICSRInvestigation

Summary

Defining URL:http://terminology.hl7.org/ValueSet/v3-ActRelationshipICSRInvestigation
Version:2.0.0
Name:ActRelationshipICSRInvestigation
Status:Active as of 3/26/14
Definition:

Description: The ways that product safety Investigations, about which information is captured in an Individual Case Safety Report, are related to each other. One investigation may be performed at a patient care institution, and the second by a manufacturer, a third by a regulatory agency. They may all investigate the same case and are thus related. Other kinds of relationships are replacement (if the mode of the Investigation is changed).

OID:2.16.840.1.113883.1.11.20353 (for OID based terminology systems)
Source Resource:XML / JSON / Turtle

References

This value set is not used here; it may be used elsewhere (e.g. specifications and/or implementations that use this content)

Logical Definition (CLD)

  • Include these codes as defined in http://terminology.hl7.org/CodeSystem/v3-ActRelationshipType
    CodeDisplayDefinition
    RPLCreplacesA replacement source act replaces an existing target act. The state of the target act being replaced becomes obselete, but the act is typically still retained in the system for historical reference. The source and target must be of the same type.
    SEQLis sequelAn act relationship indicating that the source act follows the target act. The source act should in principle represent the same kind of act as the target. Source and target need not have the same mood code (mood will often differ). The target of a sequel is called antecedent. Examples for sequel relationships are: revision, transformation, derivation from a prototype (as a specialization is a derivation of a generalization), followup, realization, instantiation.
    SPRThas supportUsed to indicate that an existing service is suggesting evidence for a new observation. The assumption of support is attributed to the same actor who asserts the observation. Source must be an observation, target may be any service (e.g., to indicate a status post).

 

Expansion

This value set contains 3 concepts

Expansion based on ActRelationshipType v3.0.0 (CodeSystem)

All codes in this table are from the system http://terminology.hl7.org/CodeSystem/v3-ActRelationshipType

CodeDisplayDefinition
RPLCreplacesA replacement source act replaces an existing target act. The state of the target act being replaced becomes obselete, but the act is typically still retained in the system for historical reference. The source and target must be of the same type.
SEQLis sequelAn act relationship indicating that the source act follows the target act. The source act should in principle represent the same kind of act as the target. Source and target need not have the same mood code (mood will often differ). The target of a sequel is called antecedent. Examples for sequel relationships are: revision, transformation, derivation from a prototype (as a specialization is a derivation of a generalization), followup, realization, instantiation.
SPRThas supportUsed to indicate that an existing service is suggesting evidence for a new observation. The assumption of support is attributed to the same actor who asserts the observation. Source must be an observation, target may be any service (e.g., to indicate a status post).

Explanation of the columns that may appear on this page:

Level A few code lists that FHIR defines are hierarchical - each code is assigned a level. In this scheme, some codes are under other codes, and imply that the code they are under also applies
Source The source of the definition of the code (when the value set draws in codes defined elsewhere)
Code The code (used as the code in the resource instance)
Display The display (used in the display element of a Coding). If there is no display, implementers should not simply display the code, but map the concept into their application
Definition An explanation of the meaning of the concept
Comments Additional notes about how to use the code

History

DateActionAuthorCustodianComment
2020-05-06reviseTed KleinVocabulary WGMigrated to the UTG maintenance environment and publishing tooling.
2014-03-26reviseVocabulary (Woody Beeler) (no record of original request)2014T1_2014-03-26_001283 (RIM release ID)Lock all vaue sets untouched since 2014-03-26 to trackingId 2014T1_2014_03_26